1. Operating treatments of floating fish feed device
( 1) Safety measures prior to starting and after quiting
① Inspect all parts of fish feed floating pellet making machine, especially the attaching screws and anchor bolts of each section of the puffing chamber, the connecting bolts in between the electric motor base and the framework, as well as the screw connection in between the puffing chamber as well as the frame, and also there need to be no looseness;
Related post: fish food pellet maker
② Manually revolve the primary shaft, currently, there ought to be no massaging audio in the fish feed floating pellet making device puffing cavity;
③ Beginning the feeding auger of fish feed drifting pellet making equipment, examine its stepless high-speed efficiency, as well as require regular procedure;
④ Check as well as clean up the water as well as gas paths before starting the fish feed floating pellet making equipment, and all filters require to be cleaned;
⑤ Prior to beginning the fish feed drifting pellet making maker, inspect whether the wiring of the electric control part is correct, whether the turning of each electric motor is proper, as well as whether the control is dependable;
⑥ After the fish feed floating pellet making device is quit, you must use high-temperature gloves, swiftly get rid of the discharge mold, and promptly tidy it while it is warm, as well as start the major motor to clear the material built up in the puffing tooth cavity. When the corn is blown, soybean powder need to be included The material is rinsed tidy;
⑦ Take notice of security when dumping the equipment, and do not stand in front of the maker to prevent danger caused by recurring stress in the fish feed drifting pellet making machine tooth cavity;
⑧ After the fish feed floating pellet making machine is running usually, it shall not be shut down at will.
( 2) Power on
① Before starting the fish feed drifting pellet making device, inspect the bolts, and also there need to be no looseness;
Related post: 8-10T/H Fish Feed Mill
② Make certain the normal supply of heavy steam as well as water;
③ Guarantee that the power supply and also electrical devices are normal;
④ Open up the steam shutoff, preheat the drifting fish pellet maker blowing chamber, the temperature level has to do with 100 degrees;
⑤ Beginning the fish feed floating pellet making maker: begin the conditioner, begin the feeding auger, when there is product draining from the electrical outlet of the conditioner, begin including steam to the conditioner.
A small amount of water is added, and the product is fed into the blowing tooth cavity at the same time. After the product is extruded by fish feed drifting pellet making machine, the puffing result and also wetness of the product are changed.
( 3) Downtime
After the fish feed floating pellet making equipment manufacturing pertains to an end, it needs to be quit. The quit sequence is: feeding auger and conditioner. Then wait up until the indicated value of the major engine existing on the electric control closet ends up being the no-load current value, after that stop the main motor and the oil pump motor.
Related post: Fish Feed Production Plant
( When the corn is puffed, regarding 25 kg of soybeans must be fed right into the bypass feeding port of the very first section of the puffing cavity. To clean up the recurring corn material in the blowing dental caries, and after that stop the major electric motor to prevent the fish feed floating pellet making device from blocking), after that promptly dismantle the puffing tooth cavity of the tail section for cleaning.
After cleaning, apply oil to the inner wall of the main shaft as well as screw head (After feeding oil), re-install it as well as wait on the following boot;
When you see that the product degree indication on the silo suggests that the product level has actually gotten to the most affordable level, start to get ready for closure. Currently, do not stop the feeding auger and also conditioner, as well as quit feeding when the primary fish feed drifting pellet making device present drops to the no-load present auger as well as conditioner.
Related post: Shrimp Feed Mill Factory
2. Operation sequence of floating fish feed equipment
( 1 )When blowing soybeans, both sections at the inlet end of the blowing dental caries are single screw heads, and also the 3 areas at the electrical outlet end are geared up with double screw heads.
Initially, add heavy steam to the jacket to preheat the puffing dental caries to concerning 100 levels, and also put the screws on the puffing tooth cavity at the tail area. After the plug is tightened up, loosen it for 3-4 turns, and after that tighten the screw plug to take care of the screw plug prior to feeding.
By managing the stepless high-speed device of the feeding auger, the feeding rate is from slow to quickly, and also the feeding speed is from small to large. After the soybean dish is ejected from the screw plug hole, add the cover to get in the typical production, and also configure the screw plugs with different apertures to obtain soybean dish with different returns as well as excellences.
By setting up the conelike stress rings of different diameters, the indicated temperature level of the four-section (discharge end) puffing tooth cavity is 130-140 degrees. It is advised that the filter of the crusher used for crushing soybeans should have a diameter of 3-4.
Related post: 6-7T/H Fish Feed Plant
( 2 )When squeezing out grainy feed by fish feed floating pellet making device, the squeezing out screws in the squeezing out cavity are all solitary screw heads, add heavy steam to the coat to pre-heat the blowing dental caries to concerning 80 levels, and go into the fish feed drifting pellet making equipment as well as vapor evenly relieved and toughened up powder.
Concerning 18%, this should be performed in the feed conditioner, and also the feed amount is regulated by the stepless rate regulating device from tiny to large. Note that the analysis of the ammeter of the primary electric motor should not go beyond the ranked current of the major engine of fish feed floating pellet making machine.
Beware of overwhelming the motor and also squeezing out grainy products. When the temperature of the squeezing out chamber at the discharge end is regulated to an ideal degree by setting up conical pressure rings with different sizes.
The above is the concept, structure and running treatments of the fish feed drifting pellet making equipment introduced by Richi Machinery. In pursuit of crunchy preference and also good appearance, makers commonly add a raising agent (or baking powder), which includes a specific amount of light weight aluminum aspects, and produces gas when heated during baking or frying, as well as the raising representative is inside the food.
For details please contact: Richi Machinery
WhatsApp：86 138 3838 9622
Email：enquiry@richipelletmachine.com
Comments